Our Work: Completed Insulation And Restoration Projects
Projects Across Kingston And Kitsap County
Since 2023, our crews have completed insulation upgrades, mold remediation, and property restoration work in Kingston, Suquamish, Poulsbo, and surrounding Kitsap County neighborhoods. Each project starts with a thorough assessment of existing conditions, moisture levels, thermal bridging, air leakage, and ends with documented improvement in building performance.
We work primarily in residential properties built between 1970 and 2010, where original fiberglass batts have settled or compressed, and where crawlspace vapor barriers have deteriorated. According to the U.S. Department of Energy, homes with properly sealed and insulated crawlspaces can reduce heating costs by 15 to 20 percent annually (source: Energy.gov, 2024). We’ve measured similar results in our own completed jobs using thermal imaging before and after installation.
Our project documentation includes photos at each stage: pre-work inspection, removal of damaged material, installation of new insulation or vapor barriers, and final thermal scan. Pazelee Harvey-Eliason, founder of Nordic Properties And Insulation, reviews every completed project to ensure it meets our internal standards for air sealing, R-value, and moisture control.
Representative Insulation And Remediation Jobs
We’ve handled a range of property types and challenge levels across the service area. Here are examples:
– **Crawlspace insulation replacement, Kingston waterfront home (2024)**: Removed water-damaged R-19 fiberglass, installed 6-mil vapor barrier, added closed-cell spray foam to rim joists (R-21), and blow-in cellulose to floor cavities (R-30). Homeowner reported a 22% reduction in propane use over the following winter. – **Attic insulation upgrade, Suquamish split-level (2024)**: Added blown fiberglass over existing compressed batts, bringing total R-value from R-11 to R-49. Sealed recessed lighting cans and attic hatch perimeter with fire-rated caulk. Thermal imaging confirmed elimination of cold spots above second-floor bedrooms. – **Mold remediation and re-insulation, Poulsbo rental (2023)**: Identified mold on crawlspace floor joists caused by a slow plumbing leak. Removed affected insulation, treated joists with antimicrobial solution (following IICRC S520 guidelines), repaired leak, installed new 10-mil vapor barrier, and re-insulated with mineral wool batts (R-23). – **Whole-house air sealing and dense-pack, Indianola cottage (2024)**: Dense-packed cellulose into wall cavities through exterior access holes, sealed all penetrations around windows and doors, and added weatherstripping. Blower door test showed reduction from 12 ACH50 to 5 ACH50.
Each project includes a written scope of work, material specifications, and post-installation thermal or moisture readings. We photograph every step and provide the full set to the property owner for records and future reference.
How We Document And Deliver Each Job
Our process prioritizes transparency and verifiable results. Before starting any insulation or remediation work, we conduct a baseline assessment:
1. **Thermal imaging scan**: Identifies existing cold spots, air leaks, and areas of missing or compressed insulation. 2. **Moisture readings**: We use pin-type and pinless meters to measure moisture content in wood framing and subfloor. Safe levels are below 19% MC; anything above triggers a moisture-source investigation. 3. **Blower door test** (optional, recommended for whole-house projects): Measures air leakage in air changes per hour at 50 Pascals (ACH50). Washington State energy code targets 3 ACH50 or lower for new construction; we aim to bring existing homes under 7 ACH50. 4. **Written scope and material spec**: Lists R-values, product brands, installation methods, and timeline.
After completion, we provide a packet that includes before and after photos, thermal images, any moisture or blower door test results, and warranty documentation for materials (most fiberglass and cellulose products carry a limited lifetime warranty from the manufacturer).
“We treat every job like it’s our own home,” says Pazelee Harvey-Eliason. “If we wouldn’t accept the work quality in our crawlspace, we won’t accept it in yours.”
Service Area And Project Types We Handle
We serve Kingston, Striebels Corner, Indianola, Rose Point, Eglon, Port Gamble Tribal Community, Suquamish, and Woodway. Our crews are familiar with the building styles and common issues in these neighborhoods: crawlspace moisture from Puget Sound proximity, attic ventilation challenges in split-level designs, and older homes with no vapor barrier at all.
Common project types:
– Crawlspace insulation (fiberglass batts, mineral wool, spray foam) – Attic insulation (blown fiberglass, blown cellulose) – Wall cavity dense-pack (retrofit insulation for existing walls) – Air sealing (caulk, spray foam, weatherstripping) – Mold remediation (following IICRC S520 standards) – Vapor barrier installation and repair – Rim joist insulation and sealing – Duct sealing and insulation (in unconditioned spaces)
We do not handle structural repairs, electrical work, or plumbing. If we discover a moisture source that requires a plumber or a structural issue that needs an engineer, we document it and refer you to licensed specialists.
Materials We Use And Why
We select insulation and air-sealing materials based on the specific application, building age, and performance goals. Here’s what we install most often:
| Material | R-Value per inch | Best application | Notes | |———-|——————|——————|——-| | Blown fiberglass | R-2.2 to R-2.7 | Attics, open floor cavities | Non-combustible, does not settle as much as cellulose | | Blown cellulose | R-3.2 to R-3.8 | Attics, dense-pack walls | Made from recycled paper, treated with borate for fire and pest resistance | | Closed-cell spray foam | R-6.0 to R-7.0 | Rim joists, crawlspace walls | Acts as vapor barrier and air barrier; higher cost per sq ft | | Mineral wool batts | R-3.0 to R-4.0 | Crawlspace floor joists, walls | Fire-resistant, does not absorb moisture, holds shape | | 6-mil polyethylene vapor barrier | N/A | Crawlspace floors | Code minimum in Washington; we prefer 10-mil for durability |
We source materials from local distributors in Kitsap County when possible. All products meet or exceed Washington State energy code requirements (WSEC Chapter 51-11). We do not use urea-formaldehyde foam or any material that off-gasses VOCs above EPA thresholds.
Getting Started With Your Project
If you want to see examples of our completed work in person, we can arrange a time to visit a recently finished project in your area (with the homeowner’s permission). For new projects, the first step is a site visit and assessment. We’ll measure spaces, take thermal images, check moisture levels, and discuss your goals (energy savings, comfort, moisture control, or all three).
After the visit, we provide a written estimate that breaks down materials, labor, timeline, and total cost. Most insulation and air-sealing projects take one to three days, depending on square footage and access. Mold remediation timelines vary based on the extent of contamination and the time needed for treated areas to dry.
Reach us at (360) 605-0721 or through our contact page. We respond to inquiries within one business day and schedule site visits within the same week for most requests.
Frequently Asked Questions
Do you provide before and after energy use comparisons?
We provide thermal imaging before and after, and we can conduct blower door tests to measure air leakage reduction. Actual energy use depends on occupant behavior, thermostat settings, and weather, so we can’t guarantee a specific percentage decrease. However, the U.S. Department of Energy estimates that proper insulation and air sealing can reduce heating and cooling costs by 15 to 20 percent in most homes. We’ve seen similar results in our completed Kingston and Kitsap County projects when homeowners track their utility bills over a full heating season.
Can I see photos of jobs you’ve done in my neighborhood?
Yes. We keep a portfolio of completed projects organized by neighborhood and job type. If you’re in Kingston, Suquamish, or Poulsbo, we can show you photos of crawlspace insulation, attic upgrades, and mold remediation work we’ve done within a few miles of your address. Some homeowners have also agreed to let us bring prospective clients by for a brief walkthrough of finished work. Ask during your site visit if you’d like to arrange that.
What happens if you find mold or a moisture problem during the insulation job?
We stop work immediately and document the issue with photos and moisture readings. We then provide a written scope for remediation (if the contamination is under 10 square feet and we can handle it per IICRC S520 guidelines) or refer you to a licensed mold remediation specialist if the problem is larger or requires containment. We do not proceed with insulation until the moisture source is fixed and affected materials are dried or removed. This protects you from wasting money on insulation that will just get damaged again.
Do you pull permits for insulation and air sealing work?
In most cases, insulation and air sealing work in existing homes does not require a permit in Kitsap County. However, if the project involves modifying ventilation (such as sealing off passive vents or adding mechanical ventilation), a permit may be required. We check with the local building department before starting any project that could trigger permit requirements. If a permit is needed, we handle the application and coordinate inspections.
How long do the materials you install last?
Fiberglass and cellulose insulation, when kept dry, can last 80 to 100 years without significant degradation. Spray foam is similarly durable if not exposed to UV light. Vapor barriers last 20 to 30 years depending on crawlspace traffic and ground moisture. Most manufacturers provide limited lifetime warranties on insulation products, and we pass those warranties on to you with your project documentation.
